Brocade 300 serial baud

As discussed above, we will be upgrading the layer 2 " S " image. So this is the file we will copy to the TFTP root directory.

VLANs provide a way of dividing up a switch or stack of switches into multiple, isolated switches this is actually somewhat simplistic, but it gets the idea across. We're creating three separate VLANs ;. By default, all ports default to VID 1. If you want to improve security, you can leave all unused ports on VID 1. In this tutorial, we need to allocate all ports for use by other equipment.

I like to do this by creating a table showing all the ports, label their external port numbers and logical numbers and then write in what will be plugged into each port. With this, it's fairly easy to mark what ports will be assigned to what VLANs.

In this example, we're showing how to cable up a pair of Brocade Ruckus ICX switches in a very typical configuration. It can drive two Anvil! In this example, we're showing how to cable up a pair of ICX switches in a very typical configuration. In this example, we're showing how to cable up a pair of ICX switches in a rather unusual configuration.

It is driving just one Anvil! The switches are going to be populated with non-Anvil! What you will configure will, of course, totally vary. The specific ports aren't the point, the planning and implementation are.

The port number is the simple integer representing the port. This is the number found above or below the physical port on the switch. We can do this in one command. Finally, the biggest VLAN. This is used when the connected switch does not support LACP. To get a license, you must purchase the license from a Brocade reseller.

To convert this into a loadable license file, you will need to get the switch's ' LID ', then create an account on " My Brocade ". In the example below, I will load two licenses, one for either switch in the stack.

This may seem silly, but consider that the upgrades are sold in lots of 4-ports at a time. This step would allow you to specify which four ports were upgraded. In our case, we upgraded them all. Call Brocade support and use the case number the switch was replaced under. With the switch being returned, there is no need to prove the old license is removed as you will be returning the switch. If you will NOT be returning the switch, then you will need to provide a show license before and after deleting the old license in order for the license to be reissued.

This is a rare case and the Brocade technician will walk you through the process should it be required. They will email you the replacement license, at which point you will license the replacement switch as if it were a new switch. Before you proceed, make sure the Firmware is the same version as the stack master.

If not, upgrade or downgrade the RMAed switch to match. Once you have the XML file, proceed from here. At this point, switch to the production switch which ever isn't being replaced. Connect the newly flashed and licensed replacement switch and you should see the configuration automatically upload to the newly replaced switch.

If you boot a stacked switch on it's own, you will not have normal access to the switch configuration. On the front of the switch will be a small "Reset" switch.

To press this, you will need a very thin object in order to press the button, like a small paper clip, needle or so on. During the boot process, press b when you see the Enter 'b' to stop at boot monitor: prompt. Jump to: navigation , search. ICX Switch configure terminal. ICX Switch config enable super-user-password secret.

ICX Switch config enable user disable-on-login-failure ICX Switch config user alteeve privilege 0 password secret. ICX Switch config show users. ICX Switch config aaa authentication web-server default local.

ICX Switch config write memory. Write startup-config done. Automatic copy to member units: 2 Flash Memory Write bytes per dot. Flash to Flash Done. ICX Switch config stack enable. Enable stacking. This unit actively participates in stacking stacking is enable. ICX Switch config exit. ICX Switch stack secure-setup. Discovering the stack topology The Equipment vendor shall have no liability for any losses or damages arising from or relating to the use of the Root or Factory account and the functionality enabled thereby by anyone other than the Equipment vendor's authorized engineers.

Proceeding with the usage of this switch as the Root or Factory user explicitly indicates your agreement to the terms of this disclaimer. Please change passwords for switch default accounts now. Use Control-C to exit or press 'Enter' key to proceed.

Please ensure the Root and Factory passwords are documented in a secure location. Recovery of a lost Root or Factory password will result in fabric downtime. All account passwords have been successfully set to factory default.

Root Cause None. Suggestions None. Comments and Reply. Feedback Add to Favorites Unfavorite. Optimize Case. How do I connect using the serial port from a laptop?

Have tried using EZswitch but it does not support this platform. All forum topics Previous Topic Next Topic. Honored Contributor. You can use any serial port communication program to connect to the console port. Try hyperterminal, putty or whatever you have.

Did this the cable come with the switches? All the switches I have are standalone non embedded and I have found out that only the cable that comes with the brocade switches works, any other standard serial cable does not.